The Counters Blog

If saving a few dollars on your epoxy garage floor coating is your primary concern or main criteria in choosing a product, you’re making a big mistake. We make it easy and straight forward for you to get professional results at a fraction of the cost. Plus they offer no guarantee against wear because they can’t, their abrasion loss ratings are too high which means their epoxies are too soft. Tires on your car can reach temperatures up to 180 degrees! Coating over your epoxy with a clear version of the same epoxy with the same abrasion rating will not solve the problem, it can actually make it worse.For office spaces with rolling chairs, retail locations with high foot traffic and shopping carts use the upgraded topcoat for best results. It also requires a different technique to achieve professional looking results. If you end up not using it just send it back to us for a full refund. You can mix and match full kit and half kits to get to right match for your floor size. Mixing bucket 1-unit of non skid additive for areas where additional traction is desired. Mix our supplied environmentally safe floor etching solution with water per packaged instructions.A second etching may be necessary for new floors due to large amounts of curing residues at the surface or older floors that are extra dirty. If your floor was power troweled you will most likely have to do two etches to open the pores of the slab. If you do not intend to rinse the grinding dust off then etching is not necessary. Once cured you can grind over it and smooth down further if needed. If you mix all the epoxy at once you will have a bucket of concrete in about five minutes. Apply a bead of the mixed base color coat from the container in a left to right direction directly to the floor do not use a roller pan. Don’t worry about the epoxy drying on the roller or squeegee, when you mix the next batch up it will reactivate the epoxy for another 45 minutes of pot life. We give you plenty of chips do achieve the look your eye thinks is best. Avoid tossing too many chips at a time so that you don’t wind up with piles of chips which will spoil the the look of your new floor. All the sections will blend together to form a single monolithic seamless finished coating. Once you have completed the first section repeat steps 3 & 4 until done. You should be done painting and applying chips in about 2 hrs per kit. Once dry to the touch sweep the floor good with a stiff shop broom or shovel with plastic edge to remove any loose chips or any chips that are sticking straight up. Apply half of the clear topcoat to seal in the chips and magnify the beautiful high gloss finish. Allow first coat to dry to the touch before applying second coat. What that means is that you are getting the best protection in the industry against tire abrasion that causes dulling and wear spots. We recommend you read the paragraph in red on the web page for a full understanding of what a topcoat is and what it’s supposed to do. We offer a straight 5 year guarantee on everything including wear, no other company will guarantee your floor against wear. Don’t be fooled by exaggerated so called lifetime guarantees that exclude everything but peeling and are next to impossible to comply with. What do you think is going to happened to those surface exposed plastic chips without a protective topcoat when hot tires with the weight of your car are twisting and turning on them. With an extremely low abrasion loss rating that’s the best in the industry this provides added protection via a chemically harder finish when working on a regular basis with heavy rolling tool chests, tools or equipment. Woodworking shops that use stationary type equipment are ok with the standard topcoat. We want to make sure you know what to do so you do it right. You can also choose to make your own color combination. Rougher surfaces and more porous surfaces will yield less coverage. Painting a concrete floor can sometimes be like painting a sheetrock wall, we’ve all had the experience of putting a coat of paint on a wall only to have it disappear completely into the wall and require a second coat. Also it’s a good idea to have a little leftover that you can put into small jars in case of an emergency. We even have a bulk sized kit which is the equivalent of 4 full sized kits. Two coats of crystal clear urethane fortified protective topcoat. Apply and scrub in well with a stiff shop broom, let stand for 10 minutes then rinse thoroughly. For best results floor must be completely clean, dry and have a slightly rough feel to it. It is extremely important that your garage floor is absolutely clean and properly etched. This is how your floor should look like prior to coating with any type of epoxy paint. Our epoxy will permanently bond into the open pores provided by etching, grinding or a combination of both. Use two measured containers to get accurate amounts of each epoxy part(2:1 ratio).

---

Rustoleum Countertop Coating Review | Duration 5 Minutes 41 Seconds We recommend doing your floor in 3-4 batches per kit, the smaller batches will allow you to apply the epoxy and chips without rushing and still have plenty of work time left over as a safety margin. Spread evenly over a 4-5 ft wide strip(you can do much larger sections if purchasing the optional spiked soles) with supplied notched squeegee. While the floor epoxy is wet, apply the supplied color chips by simply tossing them slightly up into the air and at a 45 degree angle away from you so that they freely rain down onto the epoxy in an even pattern. You can use as much of the chips as you want without worrying about running out. You will overlap the epoxy from the next section onto this area and then apply the chips. If purchasing the spiked soles you can see an alternate method a customer shared with us for spreading the chips that works amazingly well on this page below. Note: for large areas use our spike shoe bottoms which allow walking on the wet epoxy. Let the floor epoxy & chips dry to the touch, usually in approximately 5-6 hrs, you can let the epoxy cure overnight also.

---

Countertops Diy Roklook Kitchen Countertops Coating And Repair System | Duration 42 Seconds Don’t worry about scratches, any scratches in the epoxy will disappear when the clear coat is applied. The chips themselves give the floor some texture but if you desire to use the non skid additive supplied for added traction, mix it right into the second final clear coat. Clear coat dries to a touch/walk on, in about 2-3 hrs(you can move all your stuff back in at that point). Epoxy is 100% solids military grade aliphatic epoxy as opposed to water based or hybrid cyclioalipahatic epoxies. They are urethane fortified and have abrasion loss ratings of 20mgs for the standard topcoat and 4mgs for the military upgrade topcoat. It is very important that you know the difference between topcoats and epoxies.

Asphalt Shingle Coating by armorgarage.com

Two coats are recommended since most asphalt shingled roofs that need to be coated are porous and worn out and will tend to absorb the first coat, while the second coat leaves a protective surface film that stops shingle granule loss, cracking, curling and leaking. This is an important feature, many other products that are elastomerics will trap moisture that can damage your roof boards and beams. Once it’s dry, it turns crystal clear and will enhance the beauty of your shingled roof. With our bluish tint, you are assured of a complete seamless roof coating! Also, notice the way it leaves no trace once it’s dry and the project is finished. Do not apply to moist or wet roofs or if rain is forecasted within 24 hours of application. These are structural defects that no roof coating can solve. Wind will sometimes blow rain underneath the tiles, will this stop that from happening? You may solve your wind driven leaks this way but you will most likely create another more serious problem of trapping moisture in your roof since elastomerics will not let the roof breathe properly. When needed you simply apply another single coat that will bond to the original coating.

---

Rust Oleum&Reg; Countertop Transformations&Trade; Large Charcoal Coating Kit From Menards.Com Let the first coat dry for 3-4 hours and then apply the second coat. Our asphalt shingle sealer can also be used to seal all microscopic cracks in clay roof tiles to stop leakage and extend useful life. When other coatings give you a range of coverage from a low to a high area, you can rest assured that you will more than likely get the low end of coverage. Our asphalt shingle coating has been formulated with a bluish tint when wet so that you can see exactly where it’s been applied. Applying clear roof coatings from the get-go makes it easy to miss spots. Take note of the way it helps you see where you’ve applied the shingle roof coating. Use a paintable acrylic caulk for large cracks or paintable roof repair tape. Use a 1/2″” nap roller and good quality painter’s brush for hard to reach areas. The only way to solve that issue with a coating is to apply an elastomeric type coating to encapsulate the shingles. Our roof was not pitched properly will the coating prevent leaks from happening?

Full Service Premium Epoxy Flooring Installation by performancefloor.com

Our advanced equipment is custom manufactured for high production, environmentally controlled, top quality preparation methods for any and all types of flooring conditions. Coatings applied by performance can be easily and economically maintained and/or re-coated.The appearance and condition of your floors are an immediate indication of your companies attitude toward quality, safety, morale and the positive image you wish to present to your customers. We can provide you with full customer-oriented services at a competitive price. Our applicators use the most professional equipment and procedures to assure speed and simplicity of application. Our company desires that the customer is satisfied with their understanding of the work and experience of our company. Entire area will be magnetically swept to remove all spent shot. Entire area to be swept and/or power blown prior to coating. With millions of concrete applications under our belt, we have the experience to install any type of decorative system. The appearance and condition of your floors are an immediate indication of your attitude toward quality, safety, morale and the positive image you wish to present to your customers. This assures the product preparation and application is controlled by performance and warranted. Our epoxies and urethanes are formulated specifically for high impact and abrasion resistance at the most competitive prices. Our advanced equipment is custom manufactured for high production, top quality preparation methods for any and all types of floor conditions. Coatings applied by performance can be easily and economically maintained and /or re-coated. All coated area will be sanded and/or diamond ground prior to coating. Our products are all 100% solid epoxies, not the cheap, poor quality water-based epoxies that are flooding the epoxy flooring market today!