The Counters Blog

Southampton NJ Real Estate How To Attach An Undermount Sink On A Stone Countertop

What Things Are Made From Granite

How Granite And Marble Slabs Are Made | Duration 5 Minutes 2 Seconds When the paste is dry, use a soft cloth to wipe away the paste. Even if you know how to clean countertops correctly your granite will need to be resealed periodically. Knowing how to clean a granite countertop will make the sealant last and keep the counter beautiful for years. Here’s how to safely remove dirt, stains and etching from this elegant stone. Here’s how to properly clean ceramic tile and grout to keep counters beautiful and germ-free. Here’s how to remove dirt and mildew without damaging your concrete floors. These common ingredients in your kitchen can remove rust from knives, tools, even furniture. And the granite in countertops has been sealed to make it stain-resistant. Don’t use abrasive cleaner or pads, either, because granite can be scratched. For an extremely tough stain, put the paste on the spot, cover with plastic wrap and tape down the edges. Normal wear and tear will wear the sealant off, leaving the counter dull and susceptible to stains. Plan on having your granite counters resealed every two to four years.

How To Make A Table From Granite Remnants by homeguides.sfgate.com

Add a second column block directly atop the first for increased height. You can also make your own concrete blocks inexpensively using a mold, dry concrete bags and water. This is an attractive way to make a substantial outdoor table for the backyard that you will never worry about blowing over in a wind or being damaged by weather.

How Are Granite Countertops Made? Granite Shorts Ep.3 Www.Marble.Com | Duration 7 Minutes 9 Seconds For a low-slung table to display plants, take four large red-clay planting pots and turn them upside down on the patio. They are remnants only because they are too small to use for general kitchen or bathroom projects involving large countertops and backsplashes where everything must match. Contractors are unlikely to match leftover pieces to their main project stone, which means they throw away or sell smaller slabs as remnants. Unlike paint or tile, stone slabs offer a lot of variety in appearance — even when of the same type stone. Their loss is your gain, because these waste materials make wonderful small tabletops. Think carefully about where you want your table before you make it, because it will be heavy and awkward to move when finished. This raises the blocks to 16 inches, which, with a 2 inch or more thickness of your granite remnant, makes a good height for a coffee or end table. For a large table, make two or more stacks of blocks to support the granite remnant. Arrange them so each pot becomes a leg of the table, making certain that the flared edge of the pots sit inside the perimeter of the tabletop.

How To Cut Granite Slab and Tiles by bobvila.com

Granite is extremely dense and hard, so you must proceed with patience and the proper tools to get the job done. Just place two or three strips along the topside in the general area where you’ll be cutting—you’ll be cutting right through it. The wise carpenters’ adage of “measure twice; cut once” applies here. When cutting granite, you’ll have only one chance to get it right. Then, make a short “back-cut,” about two inches long, from the end of the cutline in. Making the back-cut is a must because the granite material becomes very thin just before the sawblade breaks through the last bit of stone at the end of the slab. Slurry left on a sidewalk or driveway can be easily rinsed away with a garden hose. Unlike a circular saw, which is handheld, a wet-tile saw is stationary and the tile rests on a sliding table. Drain the tile saw reservoir and wipe up any spilled or splattered water or slurry with a rag. One way to save considerable cash on your dreamy update? Here’s all the guidance you need to successfully cut granite slabs (typically 1¼” thick, but ranging up to 1½” thick) and tiles (of about 3/8” thick) for your home improvement project. Either will work, but the wet-cut circular saw will produce very little dust, thanks to a small tube that drizzles water onto the surface of the granite as you cut. By securing the piece with clamps, you’ll reduce vibration and movement of the slab, both of which can lead to chipping. Cutting granite is loud, and it’s a dusty prospect without a wet-cut circular saw. Because the tape will simply serve to protect the surface and reduce the risk of chipping, the placement of the tape needn’t be precise.

How Natural Stone Is Made | Marble.Com | Duration 2 Minutes 13 Seconds Take your time and recheck your measurements to ensure you’ll be cutting in the exact place. This will reduce the risk of the granite chipping as you cut from the other end and reach this spot. Without the back-cut, vibrations from the saw could likely cause chipping or even break off a chunk. Focus on keeping the blade aligned precisely on the cutline and maintain light and steady pressure on the saw without forcing it, letting the blade do the work. Depending on the length of the cut, this could take 15 minutes or longer. Allow the granite dust to settle and suck it up with a shop-type vacuum. Wet-tile saws vary widely; some come with lasers to help align the tiles, adjustable guides, or the ability to make beveled cuts, but they all work on the same principle. Any errant ink that remains on the tile post-cut can be removed with a bit of rubbing alcohol on a rag. Hose down outdoor surfaces with a regular garden hose if necessary.