The Counters Blog

How To Install A – 12 Steps With Pictures Microwave In Wall Cabinet



A recirculating or front-venting microwave can be installed beneath a counter without any further effort. Be aware of the requirements of your model before you begin installation.

Your microwave will need to be fastened to at least one of them. Use a small nail to probe the wall stud(s) and determine the width. If your microwave came with a wall template, tape that instead as a drilling guide before you attach the plate.Remove any decorative trimming from the cabinet preventing you from placing the mounting plate correctly.

The bottom edge of the plate should have an area covered in holes. At least one should be completely over a wall stud to support the microwave’s weight. Use the circles you drew as a guide, not the mounting plate. Otherwise, select a spot easily accessible by the power cord and out of the way of normal cabinet function. Pull the mounting plate toward you while tightening toggle screws.


Microwave Cabinet | Duration 4 Minutes 6 Seconds

With an assistant’s help, hang the microwave onto the support tabs on the mounting plate’s base. Fasten the microwave to the base of the cabinet above using screws where directed on the top template. If you are having trouble finding the vents, place the microwave on a table, plug it in, and heat food or liquid inside. There should be at least an inch of space next to each vent. If the cord will not reach or is in an inconvenient location, temporarily remove the microwave and drill a small hole in the cabinet or shelf to snake the cord through. Because the cabinet does not allow as much air movement around the vents, dust will gradually build up and increase the risk of fire.

You don’t want it very close because of the heat from the stove. My microwave goes on from itself we have to plug it out everytime why does it do that?

If in any doubt, refer to the manufacturer’s instruction manual or call the retail store you purchased the microwave from for more help. Consider using a front-venting microwave or a kit for venting the cabinet to the outside. This risks permanently destroying your microwave and starting a fire.

How to Install a   12 Steps with Pictures Microwave in Wall Cabinet

When you’re ready to fix the plate to the wall, get someone to hold the plate while you attach it with lag screws. For tips on how to install a countertop microwave, read on!

Other types may require more advanced ventilation installation. Other types of microwave may be more suited for an over the range installation, require a new ventilation hood, or even necessitate a full new ventilation system. Once you’ve located the center of one wall stud, its closest neighbors are usually located either 16 inches or 24 inches to each side. This flat metal plate should be level and the top tabs should butt against the base of the cabinet or cabinet frame. Use a level to ensure your microwave isn’t installed at a slant. If the front of the cabinet has an overhang, place the mounting plate below the back of the cabinet by an equal amount. For a microwave that requires base-of-cabinet attachments, you may need to saw off the overhang instead. Locate the two or more holes along the upper edge of the microwave. Drill a 3/16″ (5mm) hole through any circle located on a wall stud. If your microwave came with a top template, tape it to the base of the cabinet above and drill 3/8″(10mm) holes through attachment points where directed to fasten the microwave to the cabinet base. If your microwave came with a base of cabinet template, tape this where the microwave top will be located and drill where instructed for the power cord.

If there are no electrical outlets within reach of the cord, you will need to install a new electrical outlet. Have an assistant hold the mounting plate securely in the correct position as you fasten it to the wall. These will bear most of the microwave’s weight, which is why they are used over the wall studs. The “wings” of the toggle screw go through the hole and pull against the wall as the screw is tightened. Snake the power cable through the hole drilled for this purpose before attaching the microwave. Tighten until the top of the microwave and the base of the cabinet are flush. Place your hand near each side of the microwave to feel for blowing air. This is especially wise if your cabinet is high up, since the table can easily fall out of the microwave during lifting. Make sure the vents are not flush against any surfaces or objects. Wipe the vents with a damp cloth while the microwave is turned off. Microwaves use a lot of electricity when they are turned on.



Base Under Counter Microwave (Bucm) Cabinet | Duration 3 Minutes 21 Seconds

Placing a microwave’s vents against the cabinet walls or failing to clean them regularly increases the risk of fire from dust buildup. Next, position the mounting plate so it’s level with the bottom of the cabinet and drill holes over the studs and a hole for the power cord. Once the plate is in place, thread the power cord through the hole and hang the microwave on the support tabs.

How To Make A Countertop Microwave Into A Mountable Microwave by hunker.com

The kit includes a mounting plate that attaches to the bottom of a cabinet, letting the microwave oven hang above the counter. Sink the screws from the mounting kit through the holes in the mounting plate and into wall studs. Attach two of those brackets to the bottom of the mounting plate by screwing them into wall studs. As long as the wood sits flush against the top of the microwave oven, it should provide enough support to hold the oven in place. When shopping for a new microwave oven, you have the option of a mountable or a counter-top model, but it is possible to turn a counter-top model into a mountable model by using a microwave oven mounting kit. The cabinet should have wall space underneath it because the microwave oven will sit against the wall. Slide the stud finder along the wall until the device’s light flashes or you hear it beep, which indicates a wall stud is at that spot. Find other wall studs in the same way, and mark their location on the wall, too. The board will provide support and stability for the microwave oven. Align the mounting plate’s holes with marks you made for wall stud locations. Insert wood screws through the bottom of the cabinet and into the wood board.

Leave a Reply

Your email address will not be published. Required fields are marked *