The Counters Blog

<< >>

How To Remove Burn Marks From Solid Surface Countertops

Marble surfaces are more tedious-to-treat since the white backdrop is very difficult for concealing a burn mark. It should be moist, but not wet, so squeeze it to drain out the excess water. Though many folks recommend this technique for softer materials, it is useful for treating the brownish tinge of solid countertop burn marks too. However, to ensure that it is properly concealed, you should use a dedicated solid surface countertop cleaner. Each one is essentially a kit containing specially-formulated solutions and applications brushes. Then, use fine-grit sandpaper for re-shaping the minute, burnt edges of the mark. Continue rubbing with the sandpaper until the burn mark is well-concealed. Staining and issues like burn marks on the surface are a persistent problem, but removing a burn mark from solid surface countertops is not a demanding task. Granite and darker marbles are better equipped to conceal treated, burn marks since the background has a darker shade along with dense graining. Squeeze out some regular, white-colored toothpaste on to the burn mark. You can even use an old toothbrush for this to ensure that the toothpaste is evenly scrubbed into the site. Special cleaners are retailed for all the common, solid surface countertops, like granite or marble. Apply the cleaner according to packaged instructions, rubbing in the formulation repeatedly until the discoloration fades away. This is vital for camouflaging the burn mark in the background of the unspoiled surface. You can also use a countertop polish to ensure the burnt spot does not develop a visibly dull hue. Also, the treated spots should be protected from greasy foods for a few days because grime-like deposits can develop around the slightly sticky, polished edges.

Marble Repair Remedies For Burns and Cigarette Stains by countertopspecialty.com

If you look in the cabinets at the underside, it will simply be gray in color. It’s basically a plastic mold with a colored pattern and protective gel coat applied. It may be possible to sand the area down and re-apply the gel coat, but you’d most likely still have a blemish. You could experiment mixing a bleach and water solution yourself, but this is not recommended only because it almost always results in further damage since it is difficult to get the concentration right. This should remove all the burned and discolored marble, but it will leave an obvious dull spot and possible depression. Sanding “polished” marble will totally ruin the surface shine, of course. This really did the trick, with nothing further needed! You may or may not be able to fully restore the shine on the burned area. Maintenance and repair depend on the material, not where you bought it. If you are talking about cigarette burns, then consulting a marble restoration professional is your best bet. Marble burns or stains from cigarettes can be tricky depending on the type of surface finish on the marble and the degree of damage. Cultured marble will have a drip line where the gel coatings were applied and the underside will be a flat gray or beige vs. Once the surface of a cultured marble countertop is stained or scratched it’s basically toast. A cultured marble repair technician may be able to fix it, but it would probably be cheaper/easier just to replace it. It is possible that you’ll need professional restoration, but that gets expensive. However, bleach can sometimes be helpful to remove discoloring from burn marks. This marble etching destroys the surface finish leaving dull and whitish-colored spots or areas. You may have to re-finish the surface to completely remove them and that’s not something you can do yourself. The crux of the matter is that the burned/damaged marble must be removed and the damaged area restored so it matches the rest of the marble countertop. You then need to use restoration techiques to return the surface to its original look and feel. If so, how does one clean the stain, if possible to clean it at all? Theoretically, the smoke could settle on the marble countertops and build up over time and yellow the marble just like it does on walls, furniture, etc. But, this would require fairly heavy smoking and very poor hygiene. Any smoke residue on the tops will get cleaned off with regular cleaning. Cultured marble vanities are made to look like marble and will often have a built-in sink. Once cultured marble is burned, it really can’t be repaired well. If you do have a real marble vanity top , then removing burn marks is really a job for a professional to restore it to the previous condition. Now, bleach can damage (etch) marble and should not be “generally” used for marble repair or cleaning, however, this product has just the right concentration to effectively remove discoloration without causing further damage to the marble countertop.

Get Stains Out Of Your White Countertop Easily | Duration 2 Minutes 53 Seconds So, the mold remover should help lighten the color some and may remove it totally. If you do experiment with your own bleach solution, expect that you will etch (make it dull) your marble. A third, more aggressive option (if you can’t remove the burn discoloration chemically) is to sand the burn with 400 grit or 240 grit metal sand-paper. On honed marble the repair won’t be as noticeable and you can even smooth it out with 800 grit paper and 0000 grade (super-fine) steel wool. Unfortunately, there is no way to know for sure which method or combination of methods will work best in your case. I used a little at a time, and it worked wonderfully without scratching the counter top at all. It all came off, and the counter top actually looks better than before, because it actually worked out all the mild scratches that you have in a faux marble over the years. This process will remove the “polished” marble in the area leaving a dull spot with a slight depression. To do the job properly you’ll need to hire a marble restoration professional. Your best bet may be to hire a marble cleaning and restoration tech to re-surface the marble. Homeowners can successfully manage many marble repair issues, but when the marble is too damaged the only option is to hire a pro. Is there any way to remove the burns from the flat iron? If it’s a cultured marble countertop , then there isn’t a lot you can do about it yourself. It “looks” a little like marble, but it is basically plastic. A real marble vanity top can be burned, but it’s way more difficult. Burns are physical damage to the marble countertop itself and not a stain that has absorbed into the pores. Really, the best thing to do is to call a marble repair professional, especially if you have multiple burns. Removing the burned marble may cause additional damage to the marble. Removing the burned marble will change the look and feel of the surface. Possibly such a film could even absorb into the pores below the surface causing some staining.

How To Fix A Burned Bathroom Counter by homeguides.sfgate.com

If you’ve got burns on your bathroom countertop, you know by now that you can’t just wipe them off.

How To Remove A Stain From Your Granite Countertops A Demonstration By Great Lakes Granite & Marble | Duration 3 Minutes 3 Seconds Larger burned areas require the replacement of the laminate. Scrub it lightly with steel wool but don’t use too much force. Repeat two or three more times if needed to lighten or lift the stain. This works better on lighter laminates because bleach naturally tends to whiten things. Take care with bleach, though — if you spill it or use it on darker laminates, it can create white spots. It should be noted that your countertop may never look new again, but if done properly, the laminate paste method will remove, hide or help to blend the burn. Sand the patched area lightly with steel wool to smooth and further flatten the area. It involves disconnecting the plumbing, removing the sink and faucets, prying up the burned laminate and gluing a new piece in its place. Tile won’t burn, but small laminate burns can sometimes be lifted. Apply the paste to the burn and let it sit for a few minutes. It the burn is a light scorch that doesn’t penetrate deeply, the baking soda might be just enough to do the trick. Use a cotton swab to surgically dab some bleach on the burn. Allow the bleach to work its magic on the burn for a few minutes and wash it off with water and a soft cloth. If you see progress, repeat as necessary until the burn marks are removed. If the burns are deeper, and won’t respond to baking soda or bleach, laminate paste may be the solution. Use a putty knife to trowel some matching color laminate paste over the burn. If it shrinks and you see a small depression, add some more paste and repeat. It’s a bigger job, but you’ll end up with a new countertop without burns. If there’s a laminate backsplash, you’ll have to remove and replace the backsplash, too.

How To Remove Burn Marks From Countertops » How To Clean Stuff.Net by howtocleanstuff.net

Whether they are caused from a hot pan or a curling iron, the likelihood of removal all depends on the severity. Scrub the area lightly with either a scrub brush or toothbrush. Consider replacing the section or using one of our clever cover-ups below. Many companies offer special cleaners to remove burn marks and other stains. Clean the area again with the specified cleaner and polish as usual. Begin by using the soft cloth and mild soap to remove as much discoloration from the surface as possible. Apply a layer of the paste to the scorch mark and gently rub it in. Scrub the area lightly with either a soft cloth or toothbrush. Apply grout between them to create a perfect spot to set hot pots and pans. If the burn mark is large (and on a kitchen countertop) make it your new work station and cover the area with a cutting board. Moisten the sponge with water and rub on the burnt area until the mark disappears. As a result, the lighter blew up, leaving a nasty burn in the kitchen counter. Any suggestions on how to repair/fix this without having to replace the whole counter? I used a toothbrush and just the tip of a razor blade for the crevices. Apply a layer of white toothpaste to the scorch mark and allow it to set for several minutes. If the mark cannot be removed, it may have penetrated the surface, making it unable to be removed. Doing this first allows for the maximum removal prior to removing any of the surface. This will remove a thin layer of the stone so proceed with caution. Do not sand outside of the stain as this will also scratch the clean countertop and remove any sealer/finish. It may also be helpful to allow it to set for a couple of minutes. When the stain is gone, clean with water and mild soap as normal to remove any cleaning residue. Take four tiles that coordinate with your countertop and use adhesive to make a square on top of the burn. Chances are these hot pots and pans created the burn in the first place, so you can solve two problems at once! If trying to avoid replacing the entire countertop, consider purchasing just a sheet of the laminate adhesive to apply to the surface. I scrubbed hard with a sponge scrub; it came out worse, blacker than before. It discolors the countertop and where you scrubbed shows because it gets light-somewhat foggy. It is true that it will clean so well, you can see the very clean space you covered.

How To Remove Limestone Stains: 9 Steps With Pictures by wikihow.com

You must take precautionary cleaning measures to avoid damaging your limestone when removing the stains. Your vacuum can be utilized to care for your limestone, especially if you can turn off the spinning brush. The vacuum removes and dislodges dirt and dust in between cracks of the limestone. Do not wet your mop, but instead use it dry to sweep the area of unwanted dust or dirt. It’s important to remove any dirt particles before using liquids because they can scratch the surface. You can use common hand soap or use a smaller proportion of dish soap. A poultice is a mixture of ground chalk (whiting) and hydrogen peroxide. Soap scum buildup can be gently scrubbed off by using baking soda on a sponge in a circular motion. Non-acidic soap scum removers or a stone cleanser can also be used if necessary. If you have limestone countertops, you should also clean them with a dust absorbent fabric every other week. You could use a dust mop on a table or countertop as long as the mop is clean. For areas around the house that get heavy foot traffic, use rugs, mats, or runners. Similar to the condensation cups, the heat produced off hot plates can stain and damage your surfaces too. Be gentle, and use a soft attachment if possible, as to not scratch the limestone surface. Before scrubbing, wipe away or vacuum up any dirt or dust so it does not scratch the limestone. We used a brush in jointing substance on black limesone slabs and it has left a black residue on the slabs any idea on how you would remove the staining its a polymer based substance? You may have to try several times to get the stain out. When you rinse away the poultice, the stain should have disappeared. Limestone looks great, but you’ll have to put in the work to keep your surface clean. If you can’t turn off the brush, you can still do a quick vacuum of the dust and dirt of the affected area. This will also work for an elevated surface like a kitchen counter. After removing or dislodging some of the grime off the floors, mop the area. Dampen a rag by submerging it into the mixture and remove as much water as you can. Take your time and don’t hesitate to spend extra time going over the stain with the rag. Some versions will use a different chemical from hydrogen peroxide. Clean soap scum stains on limestone showers with baking soda. Dry your shower after each use to prevent soap scum buildup. Rub off stains immediately either with a damp cloth and gentle soap or brush off (if it’s soot, dirt, etc.). There are plenty of cleaning supplies that specialize in efficient, dry cleaning. You should also have outdoor mats to wipe your feet off before entering your house. For the limestone table and countertop users, use coasters! Start by cleaning the limestone with a warm water and mild liquid dish soap mixture. My bathroom has limestone tiles on the walls and there was a water leakage from the unit above staining some tiles so stains are not superficial or on the surface of the tiles. For outdoor limestone, consider using a high pressure washer. This reacts poorly with acidic solutions or substances, which can erode it over time. If you do, it’s likely your limestone will deteriorate and appear pock-marked. Apply a limestone poultice, or thick paste made of ground chalk and hydrogen peroxide, and leave it on for 48 hours. Remove soap scum stains from a shower by gently scrubbing the area with a sponge coated with baking soda, then rinse the area thoroughly.

Did You Know Smoke Is Corrosive To A Marble Fireplace Surround? by howtocleanmarble.org

Smoke is a lot more then that dirty, grimy, smelly film that covers the face of your marble surround and mantle. Your risk for etching the surface of your marble grows by the amount of time that smoky films goes untreated. The rapid cooling of these particles when your fire goes out — a by-product of incomplete combustion — is what leaves a film and odor and penetrates this porous natural stone. Smoke on a horizontal surface, like a marble hearth would be considered “free-floating smoke” — driven smoke that has lost its energy and has settled on rather than being forced into a marble surface. Scrub the surface of the marble with a plastic or natural bristle-type brush using a homemade solution of 4 parts water and 1 part hydrogen peroxide. Thoroughly rinse the marble fireplace surround with distilled water until streak-free and wipe with a dry cotton cloth. Because smoke film can corrode a marble’s finish and possibly lead to the need for repolishing, resealing or resurfacing, it’s best to incorporate the cleaning of your fireplace surround on a more regular basis — in lieu of only “seasonal” cleaning many get. You might be surprised to know that this smoke film is acidic and not only causes discoloration, but corrosion as well. In a nutshell, smoke contains remnants of fuel that didn’t burn. It’s these small particles that make smoke visible on your marble fireplace surround and they also include small droplets of wood tars. The smoke originating from a fireplace is classified as “driven smoke” meaning that when it shows up on a vertical surface, it’s because energy and pressure is behind it — this does not bode well for a porous marble surface. If this doesn’t cut through that oily smoke film go to the next step below. Understanding why smoke soot is not just any other household maintenance nuisance is the key component in how to clean a marble fireplace — and in how to protect your investment in this beautiful natural stone.

Do Quartz Countertops Stain? by quartzkitchencountertops.org

A lot of people get this confused with stain proof, which they are not. Granite countertops are the only other type that can hold a candle to one that’s made of quartz. The pores in a quartz countertop are very tight and small and that is why it is so difficult to stain this type of material. Keep in mind, however, that it is rare but not impossible to stain a quartz countertop. If you do find something on the surface of your countertop that you aren’t able to clean up you can contact the manufacturer of the product for further advice. Some users are coming up with interesting methods that seem to work for both them and others that are trying it on their quartz as well. A quartz countertop can stain but it is a lot more difficult to stain than a laminate countertop, that’s for sure. It will be difficult to find a kitchen countertop that’s easier to keep clean or maintain than a quartz one. This does not mean, however, that you should start pouring red wine on top of it and leave it to sit for a few days before cleaning it up. In most cases you’ll find that what you think may be a stain is actually just a surface substance that’s difficult to clean. It’s rare to see a stain set in when spills and mishaps are cleaned up quickly. In most cases what you think may be a stain usually turns out to be surface dirt that needs some extra scrubbing or a special cleaner to get it worked out of the quartz.

How To Get Rid Of Countertop Stains by clumsycrafter.com

My husband had no idea this huge pink stain was on the counters yesterday until he saw the pictures tonight. Removing stains from countertops is much easier than you would think. We have some quarts countertops that we have used this technique to get stains off of as well. All you need to do is pour dish soap on the stain and let it set. Any stubborn stains that are left, just reapply the soap and do it again. The good news is that you can use this technique on so many things to get stains off. Next mix a teaspoon of olive oil and a teaspoon of honey and massage into hands. I mixed a paste of baking soda with dawn, spread it over the stain, then covered it all with wax paper. Accidents happen…..but it’s how you handle them that counts! It worked like play doh and drew out some of the stain but the dish soap did the trick in the end. But, it’s not really a party unless you have the correct headwear right? Really this technique works anytime you need to draw color out of a laminate or non stone surfaces and should work on most stone countertops as well. Let it set 10 minutes for a fresh stain and a few hours for an old stain. Use a barely damp old towel to wipe away dish soap and the stain. I was little to get the kool aide stains of the counter and it’s always worked perfectly! Put on disposable deli gloves and relax for 30 minutes and then wash hands. It is amazing what it will remove and it will not harm most things either.

47 Beautiful Granite COuntertops [Pictures] by countertopinvestigator.com

It’s magnificence is blazingly obvious in our photo gallery. These pictures will convince you of its’ timeless beauty, and by the time you get to the end of the second page you’ll have no choice but to agree. The pendant lighting fixture over the island highlights the surface below. This boring white kitchen gets saved by this beautiful counter. You could entertain the whole extended family with these dueling islands. These might not be high a high end granite but they sure are pretty. That’s a wine bottle opener next to the sink, just in case you were curious. And for good reason when you consider how it instantly transforms a mundane kitchen to marvelous. How do you like that eclectic mix of browns and black? This custom kitchen uses a lot of contrast to create beautiful visual interest and depth. Consider mixing natural wood with complimentary tones of brown. So much brown but just focus on the elegance of that high end granite. Having such a large kitchen turns into quite the investment when you start to buy counters.