The Counters Blog

I do kind-of feel slightly bad for “wasting” cabinet space, when other people have to use every inch they have in their kitchens. Ultimately, we decided that the dark color would help the corner just disappear visually. We placed three cabinets in the existing window nook. Since the walls were not perfect, we scribed the toe-kick to the wall and inserted them on either side of the cabinets. The material was wide enough, the color matched, and we didn’t have to buy another more expensive side/cover panel to create these pieces! We were going to have plenty of storage in our kitchen, so we created our lower cabinet layout without needing to utilize the space in the corner. But, our layout without a corner cabinet allowed us to have the arrangement we liked best: a tall cabinet next to the refrigerator. We needed to address the gap in the corner between the two cabinets. They fit almost perfectly, but they were a few inches too short on both ends.

Amazon: Silicone Strips Stove Counter Gap Covers by amazon.com

It keeps grease and other undesirables from falling down between range and counter.
Ideas For Filling Gaps In An Ikea Kitchen Hack And The Use Of Filler Pieces | Duration 4 Minutes 9 Seconds I bought the strips so the same thing would not happen to me. Still waiting for the piece that separates the counter from the oven to straighten out. They are very flexible silicone that don’t sit very well in the crack.

Install A Vanity Sink by familyhandyman.com

And if you paint the walls at the same time, you can achieve a stunning transformation. Sinks and vanities get more use than any other fixture in your house. Fortunately, changing a vanity is relatively easy, and if you paint the walls at the same time, you can achieve a stunning transformation. All you need are basic carpentry and plumbing skills and usually just one weekend. You may decide to purchase a one-piece cabinet with a matching top, which is a bit easier to install, but the basic how-to will be the same. Turn on the sink faucet to make sure the water is completely off. Stuff a moist rag into the waste pipe to block sewer odor until you’re ready to reconnect the trap. If you have a plastic laminate backsplash, just cut the caulk seam with a utility knife where the backsplash meets the wall. Your vanity top may be glued instead of screwed to the cabinet. You may need to wiggle it back and forth a bit to free it from the wall and the cabinet. If you don’t see screws, look for large nails and use a pry bar to remove them. If this is the case, shut off the main water supply and then replace the shutoff valves. Instead of coming out through the wall as in our photos, sometimes your water supply comes up through the bottom of the vanity. When you install your new vanity later, just cut matching holes in the bottom to make way for the pipes and then install new shutoff valves once the new vanity is in place. If you have a plastic laminate top, it could be fastened to the vanity with screws or caulk. If it seems nearly impossible to get the top free from the old vanity, you may have to take the whole thing out in one piece. Use a lightweight setting-type compound to speed up the process so you’ll be able to sand and paint earlier. While it’s not impossible to paint after you install your new vanity and top, it’s sure a lot easier to do it beforehand. Wait for the patch to dry completely and then sand it smooth with the surrounding wall. Filler strips may be necessary to give your cabinet doors room to swing without rubbing against the wall. Also, build up the floor with wood strips nailed flush to the finished floor to help with leveling and make small positioning adjustments. Measuring vanity cabinets can be tricky, especially if you have a multiple-piece vanity like ours. If the cabinet has a face frame, the rear width of each cabinet is about 1/2 in. Doing this also gave us a nice, comfortable overhang for the vanity top on the left side of the completed cabinet. Remember, you can also hide small problems where the vanity meets the floor by adding a molding strip to the edge. Cut protruding shims flush after you screw the cabinets to the wall. If your cabinet has a continuous panel along the entire back, cut away a portion to get at the plumbing. Align the cabinets with the level line you made on the back wall earlier. A missed screw into a water pipe at this point will add tons of time to your project! We needed to remove a small portion from the front to allow the backsplash to fit into the corner. Get help with this part of the job to avoid marring the walls or breaking the top.

---

How To Install Filler Strips & Cover Panels Diy | Duration 8 Minutes 25 Seconds You may also need a tailpiece extension if your new vanity is higher than the old one. Let the caulk dry and you’re ready to use your new sink and vanity. Be sure to attach your supply tubes to the faucet before you set the top onto the vanity because it’s really hard to fit your hand—let alone a wrench— underneath to install the faucet later. First, apply a bead of silicone caulk to the topside of the vanity along the front and sides. You’ll need to lift it high enough to allow the drain assembly to clear the cabinet. Connect the drain to the trap (use a new trap if necessary, and if you stuffed the drain line with a wet rag, pull it out first). Now look back up at your top to make sure it didn’t slide out of position while you were hooking up the plumbing. We’ll show you how to remove the old cabinet and plumbing, choose and install a new vanity, sink, faucets and countertop.

---

Stovetop Extender Demo | Duration 2 Minutes 12 Seconds It’s no wonder they can look tired and run-down after five or 10 years. In this article, we’ll show you how to remove your old vanity and install a new one. If you don’t have shutoff valves, shut off the water supply where it enters your house. The curved pipe will be full of dirty water, so have a pan and a rag handy to wipe any spill. Use your long-blade scraper to slice through any visible glue and then pry the top off the cabinet. If you have shutoff valves under the vanity that supply the hot and cold water, be prepared for the possibility that they may leak even after you’ve turned them off (clockwise). You can get replacements at any hardware store or home center. In this case, you’ll have to shut off the main water supply and remove the shutoff valves so you can lift the old vanity away from the pipes. With the plumbing unhooked, see how your vanity top is fastened. You can usually pry it loose a bit and slip a keyhole saw between the vanity and top and cut away the adhesive. Look for screws along the top edge of the vanity and remove them with a screw gun.This makes the job tougher, but with some clever maneuvering, you’ll be able to pull it free. Be careful not to tear the drywall paper beyond the repair area. After the patch is dry, sand it smooth and even with the adjoining wall surface. You may need to taper the filler strip for a tight fit. If your finished flooring doesn’t continue under the vanity, it’s best to lay out your vanity dimensions on the wall to help position it accurately. Keep this in mind when you add up the dimensions for multiple cabinets.

---

How To Install A Cabinet Filler Strip. 41u Rack Enclosure Server Cabinet 27.6 In. Deep Built In Fans. From Adventurerstacey.Com This shifted the layout to the left just far enough to cover the edge of the old floor and meet our tile baseboard. Evenly space the cabinet sides and shim them near the back and screw them together near the back edge. Next fit the finished kick panel to the front of the cabinet. If you need to cover a bit more flooring in front of the kick panel, shim behind the front panel with thin pieces of wood before you install the panel. If an adjoining wall doesn’t allow you to set the top flush, you may need to scribe it to fit. Set the top onto the cabinets with the faucet and drain assembly in place. You’ll need to buy new washers for your trap and may need to trim pipe lengths to get everything to fit. Now you can attach the faucets and drain assembly to the sink. The biggest mistake installers make is tightening retaining nuts too tightly, which can crack the sink. Get someone to help you lift the top and gently drop it onto the cabinet. We used braided stainless flex supply lines because they’re easy to apply and maneuver. Get them hand-tight and then use a wrench for a final half turn. To prevent shifting, let the caulk set for a couple of hours before using the sink.

Gap Cap For Stoves by mileskimball.com

It’s very hard to move the stove to clean it, so this really helps. Stove counter gap cover adjusts easily and pops off for cleaning. I have had silicon and metal and only the metal ones are any good. I have a stainless stove with a black top, and my daughter and my neighbor got some too. The picture shows wider than 1 1/2 inches do you have 2 1/2 w in black ?

How To Replace and Install A Bathroom Vanity and Sink by thespruce.com

For a few hundred dollars you can make your bathroom look like a million bucks. Measure from the floor to the top of the base cabinet (not including the countertop). If the vanity is anchored to the back wall only, make sure to position the cabinet so that the vanity top will have an equal overhang on each side. Some vanity kits may come with filler strip material made of the same material as the face frame of the cabinet. Attach the filler strip to the cabinet with screws driven through the inside edge of the cabinet face frame and into the edge of the filler strip. Place two wood shims between the wood spacer blocks and the wall, driving them together slightly to create a snug fit. If the vanity is installed just against a back wall, make sure countertop overhangs equally on each side. It is not usually necessary to anchor the countertop to the cabinet in any other way since the silicone caulk will bond it to the cabinet. If you have a granite or marble vanity top use a stone sealer before using the vanity. And one of the easiest ways to update your bathroom look is to replace the vanity, countertop, sink, and faucet with a clean-looking new unit. Usually, when you buy a vanity kit, it will include the base cabinet as well as the countertop and sink that are separate from the cabinet. Repeat the process to find a second stud if possible (studs are typically 16 inches center-to-center). Once the height is marked off, place the vanity cabinet into position. If the vanity will be boxed in by a side wall, too (as in our demonstration), place the vanity cabinet so the countertop will touch the side wall and overhang on the opposite side. This may involve shaping the filler strip to fit around a baseboard or coved tile piece at the bottom of the cabinet. Using a manual coping saw or jigsaw, carefully cut out the shape of the cove base from the filler strip. Once the filler strip fits precisely, sand, stain and finish the wood strip to match the base cabinet face frame. Drive a drywall screw into the cabinet side and into the wall at a stud location, making sure the screw is long enough to extend about 1 inch into the stud. Then set the countertop/ sink assembly in place onto the cabinet. Some vanity kits, though, come with brackets that screw to the bottom of the countertop from beneath the sink.

Install Base Cabinets by lowes.com

Check the width of the piece, mark and cut the cabinet side if you need to – or use a plane for minor adjustments. This will prevent the cabinet backs from bowing when you drive in the screws. Clamp the filler piece flush to the cabinet, drill holes through the frame and attach the piece with screws.